Skip to content
English
  • There are no suggestions because the search field is empty.

Connection Hub Troubleshooting

Direct mode not connecting (IOS)

If you are able to connect to the SkyTrak or ST Plus WIFI, but the SkyTrak application is not finding the SkyTrak launch monitor, please follow the steps below.

1: Go to iPad/iPhone settings
2: Scroll down to Privacy & Security
3: Local Network
4: Find SkyTrak/SkyTrak Lite application
5: Make sure it is turned on (Green)
6: Go back to SkyTrak application after verifying that you are still connected to the SkyTrak WIFI.

Hard-close and reopen the SkyTrak application with this process: https://support.apple.com/en-us/109359

The application should say "Loading" when you reopen it initially. If not, try that process again. 

If you are unable to connect to the STPLUS/STMAX/STPRO WiFi, please double check the password:
-STPLUS: skytrakplus
-STMAX - skytrakmax
-STPRO - skytrakpro

*iPad A16 model cannot connect to the SkyTrak's access point. If Network Mode is your ultimate goal, you may set that up on a separate device, then uninstall the app from that separate device. It will connect to this model of iPad in Network Mode.

Direct Mode not Connecting (Windows)

1. Unable to connect to STPLUS/STMAX WiFi network

In most cases, when you get a message that says "Unable to connect to this Network" the network password is being entered incorrectly.
STPLUS = skytrakplus (no space, no "C" in "skytrak")
STMAX = skytrakmax (no space, no "C" in"skytrak")

2. Application says "Discovering" while connected to the STPLUS/SKYTRAK/STMAX network

-Check for and disable any present VPN adapters

Some antivirus software may impede device sync on the SkyTrak application. Norton and McAfee are two commonly reported examples. If this program came pre-installed on your PC and you do not plan to utilize the service, you may simply uninstall this application. If you do plan to use these services, please reach out to the Antivirus support team to create a firewall rule for the SkyTrak application.

If you are using an Ethernet connection in addition to your WiFi adapter, you may need to disable "Priority and VLAN" in your Ethernet adapter's settings.

  • Open the Run command dialog by pressing Windows Key + R.
  • Type ncpa.cpl and press Enter to open Network Connections.
  • Right-click your active Ethernet adapter and select Properties.
  • Click the Configure... button located just above the connection icons.
  • Switch to the Advanced tab at the top of the window.
  • Scroll down the Property list and select Packet Priority & VLAN.
  • Change the Value drop-down menu to Disabled.
  • Click OK to save your settings

 

Direct Mode not Connecting (MacOS)

1. Unable to connect to STPLUS/STMAX WiFi network

In most cases, when you get a message that says "Unable to connect to this Network" the network password is being entered incorrectly.
STPLUS = skytrakplus (no space, no "C" in "skytrak")
STMAX = skytrakmax (no space, no "C" in"skytrak")

2. Make sure you have installed the SkyTrak application from the SkyTrak website, and not the app store.

If you have installed the app from the app store already, please uninstall the current version with these steps before reinstalling from the SkyTrak Website.

3. Ensure that the connection indicator says "Discovering"

If the connection indicator at the top right of the page says "Not Connected", you may need to update your MacOS version, and confirm that your Mac meets the minimum specification of an "M" series chip/processor.

4. Enable local network toggle

Use these steps to enable the Local Network permissions for the SkyTrak application. Ordinarily if this is the issue, you will see the connection indicator vacillate between "Connecting" and "Not Connected".

5. Reinstall the SkyTrak application

-Uninstall the application completely by using AppCleaner
-After downloading the installer, drag the application to the "Applications" folder in Finder before launching

Network Mode Troubleshooting

If your device is staying on Green-Yellow-Red for more than 30 seconds after the connection indicator goes back to "Discovering", reboot the unit. If it goes back to green-red-red, the most likely cause is that the home network password was typed incorrectly. From there, you can simply reconnect to the STPLUS/STMAX WiFi network, and re-type the password to try again.

If the SkyTrak network goes back to green-yellow-red after a reboot, and it's still not connecting:
-Double check that your PC/iPad is connected to the same SSID you chose in the network scan.
-Restart the application.
-Power cycle your SkyTrak unit.
-Turn the SkyTrak off, reboot your home router, then turn the SkyTrak unit back on.

On Windows, you can always press the Windows Key on the bottom left of your keyboard to bring up your taskbar and WiFi icon, where you can check which network you're connected to.

(MacOS and iOS) If after this point you find that the connection indicator cycles between "Connecting" and "Not Connected", the local network permissions may need to be enabled for the SkyTrak Application.
-iOS
-MacOS

(MacOS) if you've tried these steps and the indicator never switches from "Discovering", follow this process:
-Uninstall the application completely by using AppCleaner
-After downloading the installer, drag the application to the "Applications" folder in Finder before launching

The other reason you may see this is because there is another instance of the SkyTrak application open in the background on another device. If you have the application installed on another platform, please make sure it is completely closed.